![]() The count is reset by entering a valid code, Presses for the programmed time duration. Reached, the yellow LED turns on solid and To program the 212e keypad, you must first enter program modeīy pressing 99 # Master Code *. User #1 is the master code it can accessĪll commands in program mode. The supervisor code can notĬhange, delete, or disable the master code Program mode, but is limited to adding andĭisabling users. Keypad self-test, to ensure that the keypad works properly. To perform the self-test, with the unit powered up, press theĪfter installing the keypad, IEI recommends that you perform the If all 12 keypresses are accepted, the keypad enters self-test (The master codeĪccesses program mode and activates the main relay to verify Verify that the master code works correctly. The LEDs alternate green, yellow, and red followed by the Open REX device and normally closed door switch:Ĥ.5 Wiring Remote Trigger as Request to Exit Use the following steps to connect the 212e keypad to a normally Use the following steps to employ the 212e keypad to shunt a normally closed zone:įigure 4 Wiring 212e Keypad to Electric StrikeĬonnect the white/orange wire (loop common) to theĬonnect the brown wire (REX Input) to the normally open Use the following steps to connect the 212e keypad to a MaglockĤ.2 Wiring the 212e Keypad to a Maglock (FailSafe)Ĭonnect the green wire (normally open) to the normallyĬlosed connection on the door position switch.Ĭonnect the blue wire (common) to the common connection Strike (fail-secure) (see Figure 4 for reference):Ĥ.3 Wiring the 212e Keypad to an Electricįigure 3 Wiring 212e Keypad to a Maglock (Fail-Safe) Use the following steps to connect the 212e keypad to an electric Then connect them to the positive on the power supply. Then connect them to the negative on the power supply.Ĭonnect the red wire (V+) to the blue wire (common), and Grease pack for the wire harness connectors.Ĭonnect the gray wire (normally closed) to the positive onĬonnect the black wire (V-) to the negative on the Maglock,Īnd then connect them to the negative on the power supply.Ĭonnect the green wire (normally open) to the positive onĬonnect the black wire (V-) to the negative on the strike, and An appropriate range is typically between 48 and 52 inches on center off theįor outdoor installations, use a weatherproof backbox and seal the ![]() Mounting height can vary depending on requirements. Template on the last page of this manual and on the unit’s container. Properly size the mounting and wire access hole, use the installation In addition, it can be flush mounted directly to the wall surface by cutting a hole in the wall. The 212e Keypad is designed to be flush mounted using a standard IEI 212e Standalone Installation/Programming Manual It allowsġ20 users as well as various keypad options. Additionally, the 212e Keypad can provide basic keyless entry by controlling a door locking device where security is not an issue. Output is timed or latched and operated by a user’s PIN code. Relay output to control any device requiring an on/off switch. The 212e Keypad is designed for convenience, and features a single Keypads mount to any standard single-gang electrical box or directly Style keypad contains illuminated clear keys that make operation in In addition, each e style keypad uses hardened keys to assure long-term, high-quality performance. ![]() The electronics for each e keypad are conformalĬoated in the manufacturing process in order to provide this level ofĪpplication flexibility. Section 1: Features and Product DescriptionĤ.2 Wiring the 212e Keypad to a Maglock (Fail-Safe)Ĥ.3 Wiring the 212e Keypad to an Electric StrikeĤ.5 Wiring Remote Trigger as Request to Exit (REX)īi-Color Red/Green LED Indicates Relay StatusĪll e style keypads are designed for both indoor and outdoor flush
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |